Phone:
(631) 473-0382

Fax:
(631) 473-2445

We Sell Quality Products at Very Competitive Prices.  
FIRE EXTINGUISHERS
 
 

WHEELED FIRE EXTINGUISHERS

 
 

 
For Additional Information and Pricing contact us at
P (631) 473 - 0382 F (631) 473 - 2445
or
tmpmarineproduct@aol.com

WHEELED FIRE EXTINGUISHERS
 
 
 
 
 

TMP Marine Products offers you an extensive variety of AMEREX Wheeled Fire Extinguishers, both “compliance” (code required) and “specialty” types. Amerex “Specialty” Fire Extinguishers are intended for use on particular types of hazards, so careful attention should be made to locate them in close proximity to the specific hazard they are meant to protect.

NOTE: The most current issue of NFPA-10 should be consulted for minimum recommended fire extinguisher types, placement and travel distances.

AMEREX Wheeled Fire Extinguishers can be easily operated by one person and are differentiated from "hand portable" types often simply on the basis of their capacity, or total weight. AMEREX Wheeled Fire Extinguishers’ are available in a variety of sizes and extinguishing agents with capacities that range from 50 to 350 pounds. Wheeled fire extinguishers are chosen for the higher capacity (volume), higher flow rates, extended fire fighting range and extended discharge time.

FIRE EXTINGUISHER TYPES
 
Water and Foam fire extinguishers utilize the cooling, soaking and penetrating effect of a 45-55 ft. stream of water. Very effective for inexperienced operators for use as a Class A fire extinguisher. Alcohol Resistant fire agent is effective on Class B fires in a wide variety of materials such as alcohols, polar solvents, hydrocarbons & combinations such as gasohol.

Regular dry chemical fire extinguishers contain a siliconized sodium bicarbonate based dry chemical with free flowing and non-caking additives. Economical Class B & C protection with lower initial cost and recharging. This chemical smothers fires in flammable liquids & pressurized gases and is electrically nonconductive.

Multipurpose dry chemical or ABC fire extinguishers contain a specially fluidized and siliconized mono ammonium phosphate chemical. It chemically insulates Class A fires by melting at approximately 350°F, coating the surface to which it is applied. It smothers & breaks the chain reaction of Class B fires and will not conduct electricity.

Purple K fire extinguishers contain specially fluidized & siliconized potassium bicarbonate dry chemical which is particularly effective on Class B flammable liquids and pressurized gases, and it is electrically nonconductive. Choice of the oil, gas, chemical and utilities industries as the preferred fire-fighting agent.

Carbon Dioxide fire extinguishers is discharge a white cloud of "snow" which smothers a fire by eliminating its oxygen. It is effective for CO2 is a clean, non-contaminating, odorless gas, safe for use on clothing, equipment, valuable documents or food.

High Performance fire extinguishers are the ultimate choice for high hazard, frequent use and extreme environment applications. Economical - lower initial cost, lower maintenance costs and greater reliability than cartridge operated extinguishers.

Class D fire extinguishers are Suitable for use on metal fires. The Class D fire extinguisher incorporates a soft flow extension applicator that ensures the operator's hands are kept away from the extreme heat, preventing inhalation of the toxic fumes caused by the burning metal.

DRY CHEMICAL STORED PRESSURE
 
Item #: AX – SP – WH ( 46” H x 21-1/2” W x 24” D )

Amerex Dry Chemical Stored Pressure - 50 lb. Capacity

Cage type protection for the cylinder. Features a durable brass, chrome plated valve with easy operating "T" type operating handle and large pressure gauge. Includes a quick release, non-kinking 25 ft. hose with large handled brass, chrome-plated ball type shut-off nozzle. Also includes easy rolling, all weather 12.5" semi-pneumatic rubber tired wheels. Corrosion and impact Resistant Red Polyurethane Enamel Paint Finish. Rugged Heavy Duty steel cylinder carriage and hose hanger assembly.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
AX495
ABC Dry Chemical
30A:160B:C 174 lbs.
DDPAX496
Regular Dry Chemical
160B:C 174 lbs.
DDPAX497
Purple
160B:C 174 lbs.
 
Item #: AX – SP – WH ( 53-1/2” H x 28” W x 40” D )

Amerex Dry Chemical Stored Pressure – 125/150 lb. Capacity

Cage type protection for the cylinder. Features a durable brass, chrome plated valve with easy operating "T" type operating handle and large pressure gauge. Includes a quick release, non-kinking 25 ft. hose with large handled brass, chrome-plated ball type shut-off nozzle. Also includes easy rolling, all weather 16" semi-pneumatic rubber tired wheels. Corrosion and impact Resistant Red Polyurethane Enamel Paint Finish. Rugged Heavy Duty steel cylinder carriage and hose hanger assembly.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
AX488
125 lb. ABC Dry Chemical
40A:240B:C 344 lbs.
DDPAX489
150 lb. Regular Dry Chemical
240B:C 369 lbs.
DDPAX490
125 lb.Purple K
320B:C 344 lbs.

NITROGEN OPERATED
 
Item #: AX – DP - WH ( 45" H x 24" W x 36" D )

Amerex Direct Pressure – Nitrogen Cylinder Operated

Features a heavy duty steel cylinder carriage and hose hanger assembly. Includes a quick release, non-kinking 50 ft. hose with large handled brass, chrome-plated ball type shut-off nozzle. Also includes smooth rolling, all weather 16" semi-pneumatic rubber tired wheels.

Features a 23 cu. ft. nitrogen cylinder with brass chrome plated valve. Operate by opening the easily accessed nitrogen hand wheel valve which directly pressurizes the the agent cylinder. Corrosion and impact Resistant Red Polyurethane Enamel Paint Finish. Heavy Duty steel cylinder carriage and hose hanger assembly.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
AX450
125 lb. ABC
40A:240B:C 335 lbs.
DDPAX451
150 lb. BC
240B:C 360 lbs.
AX452
125 lb.Purple K
320B:C 335 lbs.
 
Item #: AX – DP - WH (57" H x 34" W x 39" D )

Amerex Direct Pressure – 300 lb. Nitrogen Cylinder Operated

Features a heavy duty steel cylinder carriage and hose hanger assembly. Includes a quick release, non-kinking 50 ft. hose with large handled brass, chrome-plated ball type shut-off nozzle. Also includes 6” x 36” steel wheels.

Features a 55 cu. ft. nitrogen cylinder with brass chrome plated valve. Operate by opening the easily accessed nitrogen hand wheel valve which directly pressurizes the the agent cylinder. Corrosion and impact Resistant Red Polyurethane Enamel Paint Finish. Heavy Duty steel cylinder carriage and hose hanger assembly.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
DDPAX491
300 lb. ABC
40A:320B:C 743 lbs.
DDPAX492
300 lb. BC
320B:C 793 lbs.
AX493
300 lb.Purple K
320B:C 743 lbs.

 
HIGH PERFORMANCE STORED PRESSURE
 
Item # AX-HPST-WH ( 60" H x 37" W x 44" D )
Model # AX690 ( 53-1/2" H x 34" W x 38-1/2" D )

Amerex Stored Pressure 125 / 250 lb. High Capacity

HIGH PERFORMANCE Stored Pressure units are the finest performing dry chemical wheeled fire extinguishers available anywhere! They have a tremendous flow rate, vertical and horizontal range, fire killing ability and operator protection.

Wheels are wide footprint 36" X 6".

Exclusive features: Hot dip galvanized carriage and wheels, special corrosion resistant paint finish, lift eyes on carriage

(250 lb. models only)

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
AX573
250 ABC
40A:160B:C 775 lbs.
DDPAX574
250 BC
160B:C 775 lbs.
AX575
250 Purple K
16.B:C 775lbs.
AX690
125 Purple K
120B:C 400lbs

 
REGULATED PRESSURE
 
Item # AX-RP-WH ( 52" H x 26" W x 38" D )

Amerex Regulated Pressure

These 110 ft nitrogen3 cylinder operated models feature a pressure regulator and two wheel options. The older, traditional design allows for adequate pressure to assure a smooth, complete discharge of the dry chemical with pressure reserve for blowing down the discharge hose. With 16" semi-pneumatic rubber tires. Easy to transport and operate by one person.

Exclusive features: Stainless steel collars, chrome plated brass cap, brass fittings, live swivels and bi-lingual abels.

Meets Transport Canada requirements.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
DDPAX467
125 lb. ABC
40A:240B:C 404 lbs.
DDPAX468
150 lb. BC
240B:C 469 lbs.
DDPAX469
125 Purple K
320.B:C 404lbs.
 
Item # AX-RP-WH ( 52" H x 26" W x 38" D )

Amerex Regulated Pressure

These 110 ft nitrogen cylinder operated models feature a pressure regulator and two wheel options. The older, traditional design allows for adequate pressure to assure a smooth, complete discharge of the dry chemical with pressure reserve for blowing down the discharge hose. With 6” x 36” or 2-1/2” x 36 steel wheels (non-sparking treads). Easy to transport and operate by one person.

Exclusive features: Stainless steel collars, chrome plated brass cap, brass fittings, live swivels and bi-lingual abels.

Meets Transport Canada requirements.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
DDPAX470
125 lb. ABC
40A:240B:C 432 lbs.
DDPAX471
150 lb. BC
240B:C 457 lbs.
DDPAX472
125 Purple K
320.B:C 432lbs.

33 GALLON FFFP FOAM
 
Item # AX-FFFP-WH ( 57" H x 34" W x 39" D )

Amerex 33 Gal. Direct Pressure Premix FFFP Foam

The Model 630 contains a premixed FFFP (film forming fluoroprotein) alcohol resistant foam which is highly effective on Class B fuel fires and a penetratingand wetting agent on fires involving Class A materials. Excellent when used as a vapor suppressant on fuel spills to prevent ignition. Quality hardware throughout including the

unique agent cylinder fabricated entirely of stainless steel - no interior coatings are necessary. Model 630 meets NFPA requirements for hospital helicopter pad protection.

Exclusive features: Brass fittings, stainless steel collar, brass cap, live swivels.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
DDPAX534
Recharge for model #630- 2 1/2 gal
DDPAX630
33 Gal direct pressure FFFP
20A:160B 390 lbs.

 
CLASS D
 
Item #AX-D-WH ( 52" H x 28" W x 45" D )

AMEREX CLASS D

Two choices for large volume Class D (flammable metal) protection. Model 680 (Sodium Chloride) is effective on magnesium, sodium, potassium and sodium potassium alloy fires. Model 681 (Copper Powder) designed particularly for fighting difficult lithium fires. Well

balanced for quick transport on 36" non-sparking rubber tread steel wheels. Both are pressurized with Argon and regulated to a low 125 psi to avoid disrupting the burning materials.

Exclusive features: Brass fittings, stainless steel collar, brass cap, live swivels.

USCG APPROVED


Extension Wand is Standard

PART # AGENT U L RATING SHIP WT.
DDPAX680
150 lb. Regulated Pressure - Sodium Chloride
444 lbs.
DDPAX681
250 lb, Regulated Pressure - Copper Powder
544 lbs.

 
CARBON DIOXIDE CO2
 
Item # AX-CO2-WH ( 47" H x 23" W x 48" D )

50 lb. CARBON DIOXIDE

Large volume CO2 protection provided in 50 lb. government specification wheeled extinguisher. Rugged construction and easy to operate with a "quick opening" 'T' handle valve and horn mounted shut-off valve. A logical choice in areas where a Class B:C

non-contaminating agent is required and where hand portable extinguishers are not available.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
AX333
50 lb. CO 2
20B:C 257 lbs.
 
Item # AX-CO2-WH

100 lb. CARBON DIOXIDE

Large volume CO2 protection provided in 100 lb. government specification wheeled extinguisher ( two 50 lb. cylinders ). Rugged construction and easy to operate with a "quick opening" 'T' handle valve and horn mounted shut-off valve. A logical choice in areas where a Class B:C non-contaminating agent is required and where hand portable extinguishers are not available.

USCG APPROVED

PART # AGENT U L RATING SHIP WT.
AX334
100 lb. CO 2
20B:C 461 lbs.

 
HALOTRON I
 
# AX-HALOTRON I-WH

Model #DDPAX673 ( 58" H x 28" W x 39" D)
Model #DDPAX674 ( 64" H x 30" W x 42" D)
Model #DDPAX675 ( 64" H x 37" W x 43" D)

HALOTRON I WHEELED FIRE EXTINGUISHER

The Amerex Halotron I ™ extinguishers feature the same qualities found in all Amerex products and adds the convenience of a "clean" extinguishing agent. Halotron I™ extinguishing agent has proven itself as the leader in the hunt for an alternative "clean" agent by being the only alternative "clean" agent to obtain FAA approvals for both ramp use (ARFF Vehicle) and on-board an aircraft. Combining the quality of

Amerex products with a proven alternative "clean" agent, the Amerex Halotron I™ wheeled extinguishers offer you the best value in the industry. DDPAX 673 & DDP674 – 16” Rubber Wheels and DDPAX674 has 6” x 36” Non-sparking steel wheels

  • EPA approved "Clean Agent" for Class A, B, and C hazards
  • Low GWP (Global Warming Potential)
  • Low ODP (Ozone Depletion Potential)
  • Short Atmospheric Lifetime
  • Maximum visibility during discharge
  • No thermal or static shock
  • No electrical conductivity back to the operator

Exclusive features:
Brass fittings, live swivels, reflective stripes, tow loops

USCG APPROVED

DDPAX674
DDPAX675
PART # AGENT U L RATING SHIP WT.
DDPAX673
65 lb. Halotron I -16 " wheels
4A:60B:C 286 lbs.
DDPAX674
150 lb. Halotron I -16 " wheels
10A:80B:C 512 lbs.
DDPAX675
150 lb. Halotron I -36 " wheels
10A:80B:C 610lbs.

 
WHAT TYPE OF FIRE EXTINGUISHER TO USE
 
It is natural for a person to use the fire extinguisher located nearest to the fire, making it essential that the correct type and size be placed in close proximity to a potential hazard.

All fire extinguisher nameplates have either the letter or picture symbols shown below. Anyone who might be expected to use a fire extinguisher should be familiar with the letter, or picture symbols identifying the type/s of fire on which it may be used. The newer picture symbols use the International sign system diagonal red slash to indicate a potential hazard if the extinguisher is used on that particular type of fire. Absence of a type symbol means only that the unit is not recommended as particularly effective for that class, but not dangerous if used in error.


 
 
For Additional Information and Pricing contact us at P (631) 473 - 0382 F (631) 473 - 2445 or tmpmarineproduct@aol.com