Phone:
(631) 473-0382

Fax:
(631) 473-2445

We Sell Quality Products at Very Competitive Prices.  
COLLIGO MARINE
Bringing Innovative Solutions to the Marine Industry

 
TMP Marine Products

Dealer For


 
TMP MARINE PRODUCTS is a Dealer for the Colligo Marine Line of fine marine products. Colligo Marine, LLC is a product development firm focused on the marine industry and provide innovative product solutions to boaters everywhere. At Colligo Marine, our group of engineers have a passion for boating and the marine industry and most of the products are conceptualized from real world experience - Real world challenges.

If you have a product challenge and need assistance with design work please contact TMP Marine Products phone (631) 473 - 0382 Fax (631) 473 - 2445 or e-mail us at tmpmarineproduct@aol.com

EMERGENCY SHROUD KITS
 
Imagine yourself on a slogging upwind tack. Rough seas have been shaking the rig for hours, jostling you into a wind-wearied reverie. A casual glance up the leeward shroud sets you instantly alert: the stay is giving way at the mast fitting and will surely fail under tension on the opposite tack.



On most boats your next step would be to fetch the massive coil of wire rope that's been rusting in the bilge all season, lug it on deck, search for the appropriate Sta-Lok fittings from the massive collection you have no choice but to keep onboard, and continue the arduous process of preparing a replacement shroud.


On a boat equipped with Colligo Marine's Emergency Shroud Kit your situation would be no less dire, but your method of repair could be a little less toilsome.

 
For sailors, a broken shroud isn't just inconvenient - it signals an expensive emergency repair job, as much as $600 or more, depending on the rigging. Currently, having spare shrouds on board is the solution. But they are large, heavy and over time will rust from the sea air. Underway, the repair can be complex and time - consuming. Carrying enough parts for all of the shrouds and mast / deck connections can also be expensive and take up storage space.

The lightweight, rustproof, reusable Emergency Shroud Kit - a 2009 Pittman Innovation Award winner - is an easy to use, temporary replacement for broken shrouds, or stays up to 50 feet long ( up to 1/4 inch wire ) - at about half the cost. The kit stores in a small, waterproof, re-sealable plastic bag that can be stowed anywhere on board.

The Colligo Synthetic Systems Emergency Shroud Kit is available ready to use in two sizes: For up to 50 foot shroud or stay to temporarily replace up to 1/4 inch wire with 7mm Dynex Dux: or for up to 65 foot shroud, or stay to temporarily replace up to 3/8 inch wire with 9mm Dynex Dux. Custom kits are also available.

One Line Terminator end fitting is pre-spliced while the other included Terminator end fitting can be spliced to the length needed. Terminator end fittings enable each end to be lashed on with the enclosed 20 feet of synthetic lashing line, or pinned to hardware if possible. Chafe Guard is included for spreader ends.


 
The Colligo Lashing Cleat eliminates the risk of lashing line knots that can loosen or shake out. Features a lockable cam that secures lashing lines, so there’s no need to tie off lashings on lashed shrouds. The patent-pending, fool-proof cleat is simple to set and adjust and allows shrouds to be tightened with halyards from above. Precision-machined from billet aluminum, the strong, lightweight Lashing Cleat is easily installed on new or existing Colligo Line Terminator™ End Fittings.

 
A shroud failure or, worse, a dismasting is a real threat to any sailor, especially those venturing offshore. While some cruisers carry extra wire shrouds and some racers carry extra lengths of Element C6 or PBO fiber, most sailors simply trust that their standing rigging will continue to stand. Colligo Marine’s Emergency Shroud Kit is a very clever, very important piece of gear that enables a skipper to carry a spare without sacrificing stowage space or adding weight. The kit includes a line terminator, a length of Dynex Dux fiber (12-strand, pre-stretched Dyneema SK-75; lengths vary based on kit, with custom lengths available upon request), splicing instructions, as well as lashing cord and chafe guards for where the emergency shroud passes through the spreaders. There’s no worry about the Dyneema ever rusting, and the kit is small.

 
EMERGENCY SHROUD KIT 7MM #CS1000
 
Temporary replacement for up to ¼” wire stays or shrouds.
Easily stowable, light and will not corrode.
Replaces up to 50 feet long shroud or stay.
Just splice on one Line Terminator™ to the desired shroud length and lash both ends on with the provided lashing line.

Kit Contains:

  • 1 unspliced, Line Terminator™.
  • 55 ft, 7 mm, 15,000 lb Breaking Strength, Synthetic
  • 12 strand line (Dynex Dux) with a Terminator™ spliced on one end.
  • 20 feet of Lashing line for lashing both ends.
  • 6 Inch piece of chafe protection for spreader ends.
  • Fids for Splicing.
  • Easy, water resistant, splicing instructions.
  • Water resistant 15” x 12” x 3” package.

EMERGENCY SHROUD KIT 9MM #CS1100
 
Temporary replacement for up to 3/8” wire stays or shrouds.
Easily stowable, light and will not corrode.
Replaces up to 65 feet long shroud or stay.
Just splice on one Line Terminator™ to the desired shroud length and lash both ends on with the provided lashing line.

Kit Contains:

  • 1 unspliced, Line Terminator™.
  • 71 ft, 9mm, 24,000 lb Breaking Strength, Synthetic
  • 12 strand line (Dynex Dux) with a Terminator™ spliced on one end.
  • 20 feet of Lashing line for lashing both ends.
  • 6 Inch piece of chafe protection for spreader ends
  • Fids for Splicing.
  • Easy, water resistant, splicing instructions.
  • Water resistant 15” x 12” x 3” package.
 
CHAINPLATE DISTRIBUTOR
 
Chainplate Distributor, 1/2", Black

  • Designed for conventional chain plates, up to ¼ inch thickness.
  • 1/2” pin hole. ?
  • 7,500 lbs-f Safe Working Load.
  • 15,000 lbs-f Breaking Strength.
  • MODEL # CSS61BLK
 
Chainplate Distributor, 3/4-7/8”, Black
  • Designed for conventional chain plates, up to 13/16” (21mm) thickness.
  • 3/4" to 7/8” inch pin hole for flexibility.?
  • 20,000 lbs-f Safe Working Load.
  • 40,000 lbs-f Breaking Strength.
  • MODEL # CSS63BLK
 
Chainplate Distributor, 5/8", Black
  • Designed for conventional chain plates, up to1/2 inch thickness.
  • 5/8” pin hole.?
  • 10,000 lbs-f Safe Working Load.
  • 20,000 lbs-f Breaking Strength.
  • MODEL # CSS62BLK
 
Male Distributor, 1/2", Black
  • Designed for Carbon Chainplates, Turnbuckle Setups, or Diamond Stays.
  • 1/2” pin hole. ?
  • 7500 lbs-f Safe working load.
  • 15,000 lbs-f Breaking strength.
  • MODEL # CSS91BLK
 
Male Distributor, 5/8", Black
  • Male DistributorDesigned for Carbon Chainplates, Turnbuckle Setups, or Diamond Stays.
  • 5/8” pin hole.?
  • 10,000 lbs-f Safe Working Load.
  • 20,000 lbs-f Breaking Strength.
  • MODEL # CSS92BLK
 
Our Patent Pending Line Terminator end fittings are the only spliceable, lashable, and pinable end fittings available that meet Hampidjan's recomended 5/1 bending ratio for Dynex Dux. This is essential for long term durabilty of Heat Stretched, Dynex Dux, UHMWPE line as the work hardening makes the line much stiffer and tight bending radii cause compressive stresses that weaken the line considerably.
 
ROLLER FURLER
 
 
The CN3 and CN5 Furlers are designed for headsails such as gennakers, screechers, code zeros or even staysails. Just roll them up and drop them down.

Our Furlers feature:

--Large diameter sheaves for handling sails in demanding conditions.
--Heavy duty sealed thrust bearings in a sealed housing ensure no corrosion problems and no maintenance.
--Designed for a continuous drive line so you never run out of line when rolling up your sail.
--Precision machined from billet aluminum for strength and light weight.
--Colorful blue/gold anodizing.
--Simple, no maintenance, line guide allows easy line changes.
--Easy to change furling line.
--Designed for use with line terminators spliced into luff line.

 
The CN5 Furler is designed for headsails such as gennakers, screechers, code zeros or even staysails. Just roll them up and drop them down.

  • Our Furlers feature:

  • Large diameter (7.5 in) sheave for handling sails in demanding conditions.
  • Heavy duty sealed thrust bearings in a sealed housing ensure no corrosion problems and no maintenance.
  • Designed for a continuous drive line so you never run out of line when rolling up your sail.
  • Precision machined from billet aluminum for strength and light weight.
  • Colorful blue/gold anodizing.
  • Simple, no maintenance, line guide allows easy line changes.
  • Good for sailboats to 48 feet.
  • 6000 lbs Safe Working Load.
 
The CN3 Furler is designed for headsails such as gennakers, screechers, code zeros or even staysails. Just roll them up and drop them down.

  • Our Furlers feature:

  • Large diameter (6 in) sheave for handling sails in demanding conditions.
  • Heavy duty sealed thrust bearings in a sealed housing ensure no corrosion problems and no maintenance.
  • Designed for a continuous drive line so you never run out of line when rolling up your sail.
  • Precision machined from billet aluminum for strength and light weight.
  • Colorful blue/gold anodizing.
  • Simple, no maintenance, line guide allows easy line changes.
  • Good for sailboats to 32 feet.
  • 3000 lbs Safe Working Load.
 
LINE GUIDES and PADEYES
 
 
Custom color shown

We have created a line of billet aluminum deck hardware. Made from 6061-T6 billet aluminum, these are innovative, colorful, and lightweight line guides and padeyes that offer bright anodized finishes with teflon impregnation for minimum line wear. All of our billet hardware is offered in black, hardcoat marine grade anodizing. Custom colors available upon request.

Line guides and padeyes are for up to 1/2 inch (12mm) line. Designed for use with 1/4 inch flat head bolts.
Great for organizing lines in front of winches!
Industry first, 2 piece line guides!
Our 2 piece line guides are designed just for continuous (looped) lines for Headsail Furlers! No more getting your fairleads spliced into the line!
Each billet aluminum piece comes with our patented sealant groove for easy installation.
Our padeyes are designed for rope shackles but can be used with steel shackles also. Large diameter radii for low rope wear.

 
#CN43BLK

1 PIECE - 1 LINE

One Eye – Center Pad

 
#CN34BLK2

2 PIECE - 2 LINES

New! Two Piece Line Guide
New Lightweight Design
Weighs 4 oz, 113 grams!

Designed for continuous line furler lines. Makes changing furlers much easier.
Billet Aluminum, Hardcoat Anodized with Teflon Impregnation.
Available in Black.

 
#CN33BLK1

1 PIECE - 1 LINE

Billett Aluminum, Hardcoat Anodized with Teflon Impregnation. Available in Black.

 
#CN33BLK2

1 PIECE - 2 LINES

Billett Aluminum, Hardcoat Anodized with Teflon Impregnation. Available in Black.

 
#CN34BLK4

2 PIECE - 4 LINES

Billett Aluminum, Hardcoat Anodized with Teflon Impregnation. Available in Black.

 
#CN33BLK4

1 PIECE - 4 LINES

Billett Aluminum, Hardcoat Anodized with Teflon Impregnation. Available in Black.

 
 
#CN44BLK



Small Center Padeye

 
BRIDLE PLATE MOORING SYSTEM
 
This unique Colligo Marine Bridle Plate Mooring System, sold by TMP Marine Products, eliminates line to line interference, as well as no more tangled mooring lines and the lines tend to last much longer. Simple, lightweight and corrosion-resistant, the galvanized system maintains mooring line separation to minimize chafe and safely allows redundant lines to the mooring. Two versions are available – one with eyebolt shackles and a premium system with "safety" shackles that uses nuts with cotter pins for extra security.

***Bridle Plate Mooring System shown mounted on top of mooring ball for illustration only. We recommend mounting below the ball, directly to the chain for maximum strength.
 
Colligo Marine Bridle Plate Mooring System is manufactured from a half-inch-thick plate available in either stainless steel or hot-dipped galvanized—Extra Large 3/4" jaw and jaw swivel and 5/8" shackles - comes fitted with a swivel (with a working load of 8,000 lbs.- force) and either two or three galvanized shackles sized at 5/8 inch attached to the plate.

The company fabricates two models, one for monohulls (two mooring line attachment points) and one for multihulls (with three line attachment points). The steel plate that forms the meat of the Colligo Engineering's Mooring Bridle Plate is fashioned from half-inch stock.

#CN11

MONOHULL BRIDLE PLATE SYSTEM

Hot dipped Galvanized. Includes Swiveling, Monohull Bridle Plate with 2, 5/8 inch HDG shackles. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

 
#CN11S

MONOHULL BRIDLE PLATE SYSTEM w/ Safety Swivel and Shackles -

Hot dipped Galvanized. Includes Monohull Bridle Plate with 2, 5/8 inch HDG safety shackles and 1, 3/4 inch HDG safety Swivel. Safety shackles and swivels feature nuts with cotter pins so no seizing is needed. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

 
#CN11

MULTIHULL BRIDLE PLATE SYSTEM

Hot dipped Galvanized. Includes HDG Multihull Bridle Plate with 3, 5/8 inch HDG shackles and 1, 3/4 inch HDG Swivel. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

 
#CN12S
LATE SYSTEM w/ Safety Swivel and Shackles

Hot dipped Galvanized. Includes Monohull Bridle Plate with 2, 5/8 inch HDG safety shackles and 1, 3/4 inch HDG safety Swivel. Safety shackles and swivels feature nuts with cotter pins so no seizing is needed. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

NOTE: The Bridle Plate is so substantial that it requires you to have an appropriately sized mooring ball.



The COLLIGO MARINE Bridle Plate Mooring System is currently being sold by TMP MARINE PRODUCTS

HURRICANE MOORING SYSTEM
 
 
Colligo Marine's patented hurricane anchor system helps boat owners in the path of storms anchor their vessels securely - even in the highest winds and waves.

The Colligo system allows for the placement of three anchors on a swivel and three lines back to the boat. The boat can then swivel on the anchors without getting anchor chains and lines twisted around each other. The minimum breaking strength for this heavy-duty system is over 30,000 lbs. It comes complete with galvanized bridle plates, shackles and a swivel. Mono and multi-hull models are available.

Monohull Hurricane Anchor System

#CN21S

Hot dipped Galvanized. Includes Monohull Bridle Plate on one end with 2, 5/8 inch HDG safety shackles and 1, 3/4 inch HDG safety Swivel connected to a Multihull Bridle on the anchor end with 3, 5/8 inch HDG safety shackles. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

 
Monohull Hurricane Anchor System

#CN21

Hot dipped Galvanized. Includes Monohull Bridle Plate on one end with 2, 5/8 inch HDG shackles and 1, 3/4 inch HDG Swivel connected to a Multihull Bridle on the anchor end with 3, 5/8 inch HDG shackles. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

 
Multihull Hurricane Anchor Safety System

#CN22S

Hot dipped Galvanized. Includes Multihull Bridle Plate on one end with 3, 5/8 inch HDG safety shackles and 1, 3/4 inch HDG safety Swivel connected to a Multihull Bridle on the anchor end with 3, 5/8 inch HDG safety shackles. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

 
Multihull Hurricane Anchor System

#CN22

Hot dipped Galvanized. Includes Multihull Bridle Plate on one end with 3, 5/8 inch HDG shackles and 1, 3/4 inch HDG Swivel connected to a Multihull Bridle on the anchor end with 3, 5/8 inch HDG shackles. 8,000 lbs-f safe working load. Good for boats 25 to 60 feet.

 
BUNGY
 
 
Simple add on product to increase energy absorption of Docklines or Mooring Lines.

Can easily be installed without a free end of the line.

The Bungy can be used in series as shown in the pic to increase stretch capabilities.

Made of a Durable rubber compound.

We highly recommend this product for high wind situations, expecially for Docklines.

Easy to store until you need them.

 
MOORING LINES
 
Our lines offer:

Premium Nylon for the Ultimate in stretch characteristics to minimize the loads input into your boat.

Double Braided construction gives the very best chafe protection. The inner core maintains most of the strength of the warp while the outer layer protects against chafe.

3/4 inch diameter gives an average tensile strength of over 19,000 lbs.

Splices and whipping are the best you will ever see.

ML25 - 25 FEET
ML40 - 40 FEET
 
SOFTIES
 
I'm sure I'm not the only one who has watched a shackle pin bounce over the side, leaving a useless U of stainless steel in my hand.


Nor am I alone in my disappointment at the mess they can make of an aluminum toe rail.

A 21st century solution has arrived - the soft shackle. Made from 12-strand Dyneema UHMWPE, it's light, chafe-resistant and hurts a lot less when you drop it on your foot.

 
Lightweight Soft Shackles and Hanks made from Dyneema UHMWPE 12 strand.

Super Strong and Chafe Resistant!

Handy lanyard for easy opening.

Slip Ring for extra security.

Self Tightening Spliced loop connection.

Lightweight replacements for steel shackles.

Headsail Hank solution for synthetic forestay's.

Individually pull tested to the SWL to set the knot.

Easy to use: Just pull the lanyard to open the

splice, then slide the loop over the shake

resistant knot. Pull the loop closed and slide

the slip ring up to the knot and you are ready to go.

2 sizes:

-2000 lbs-f SWL

-4000 lbs-f SWL

Custom sizes available on request.

Softie, Soft Shackle or Hank, 2,000 lbs-f SWL

Approx 1/4 inch diameter that makes an approximate 1.5 inch diameter loop when closed. SWL of 2,000 lbs-f. Breaking strength over 5,000 lbs-f. Pull tested to set knot. Made from Dyneema SK-75 UHMWPE line. Treated with Duracoat for UV Resistance. Handy Lanyard for ease of removal. Just pull on the lanyard and the loop opens up. Shackle is designed such that when tension is applied the loop becomes tighter, making it even more difficult for the loop to become detached. O-rings attached for extra security.

Custom Made Lengths available. Just Email or Call.

 
Softie, Soft Shackle or Hank, 4,000 lbs-f SWL

Approx 3/8 inch diameter that makes an approximate 1.5 inch diameter loop when closed. SWL of 4,000 lbs-f. Breaking strength over 10,000 lbs-f. Pull tested to set knot. Made from Dyneema SK-75 UHMWPE line. Treated with Duracoat for UV Resistance. Handy Lanyard for ease of removal. Just pull on the lanyard and the loop opens up. Shackle is designed such that when tension is applied the loop becomes tighter, making it even more difficult for the loop to become detached. O-rings attached for extra security.

Custom Made Lengths available. Just Email or Call

 
COMPLIMENTARY RIGGING DESIGN
and COST COMPARISONS
 
NEW!
 
 
Colligo Rigging Design
  • Synthetic Standing Rigging Design and Retrofit Engineering Services utilizing
    Dynex Dux, 12 Strand line.
  • Complimentary design services for retrofitting and new boat fit out using
    Colligo Synthetic Systems Standing Rigging Hardware with Dynex Dux,
    UHWPE line.

Call or email for more information

Services include:

  • Sizing Dynex Dux, UHMWPE line for your boat based on creep and stretch
    requirements and predicted loads.
  • Design and fitting of hardware interfaces at mast connections and deck fittings, chainplates, spreader ends, etc. All interfaces at Boat/Mast and Synthetic Line are engineered for long term durability, to maximize strength and minimize weight. Modifications of existing hardware and custom designs are all options.
  • Line splicing recommendations based on service needs. Based on our experience with Dynex Dux we will recommend splicing techniques to suit various load and packaging conditions
  • Completed cost comparison of Colligo Synthetic Systems Standing Rigging to stainless wire system.

For more info contact TMP Marine Products at P (631) 473 - 0382 F (631) 473 – 2445

E-mail to: tmpmarineproduct@aol.com

Tony Pira


For Additional Information and Pricing contact us at P (631) 473 - 0382 F (631) 473 - 2445 or tmpmarineproduct@aol.com